You have no items in your shopping cart.

Subtotal: Ksh0.00

Pioneer GM-D9605 2000Watts Class D 5 Channel Amplifier

More Views

Ksh28,500.00

Pioneer GM-D9605 2000Watts Class D 5 Channel Amplifier

Be the first to review this product

Availability: In stock

5-channel car amplifier
75 watts RMS x 4 + 350 watts RMS x 1 at 4 ohms
100 watts RMS x 4 + 600 watts RMS x 1 at 2 ohms
200 watts RMS x 2 bridged at 4 ohms + 600 watts RMS x 1 at 2 ohms
CEA-2006 compliant
Class-D amplifier design
variable high- and low-pass filter (40-500 Hz, 12 dB/octave) on 4-channel section
variable low-pass filter (40-500 Hz, 12 or 24 dB/octave) on sub channel
variable bass boost (0-18 dB at 50 Hz) on sub channel

Details

Features

CEA 2006 Compliant: The Pioneer GM-D9605 5-channel amplifier power ratings are measured according to the Consumer Electronics Association's CEA-2006 standards. These standards allow you to accurately compare the rated power output of all CEA-2006 compliant amplifiers, even from different brands. Manufacturers who adhere to the standards can display the CEA-2006 logo on their products and packaging. The amp has the following specifications:

  • Power Output:
    • 75 watts x 4 + 350 watts x 1 at 4Ω (with 1% THD+N)
    • 100 watts x 4 + 600 watts x 1 at 2Ω
    • 200 watts x 2 + 350 watts x 1 at 4Ω bridged
  • Signal to Noise Ratio: 75 dBA

Class-FD Amp: A Class-D amplifier offers higher power in a smaller chassis than conventional Class-AB amp designs. Pioneer's exclusive Class-FD design not only delivers full-range Class-D amplification, but is more efficient than other designs. The result is clear full-range sound in a small amplifier. The ultra-compact design provides many installation options.

Channel Layout: The GM-D9605 is a 5-channel amplifier. The channels are labeled A (left and right), B (left and right), and SW (subwoofer). The left and right channels of both A and B can be bridged with an output of 200 watts (at 4Ω) for each, plus 350 watts for the SW channel.

Auto Turn-on: When using a high voltage speaker level input, a signal sensing circuit will automatically turn the amp on and off along with the source unit. This prevents the need for running a system remote control wire (turn-on lead).

Controls

Input Select Switches: The amplifier has two input select switches that allow you to choose the preferred input mode. For the A and B channels, the 4-channel mode requires that two pair of RCA inputs be connected to the amplifier's A and B inputs, while the 2-channel mode only requires one pair connected to the A inputs. If you have a separate RCA input for the SW channel, the SW Input Select should be in the SW position. If you do not have a separate SW input, the switch should be in the A/B position, and the SW channel will receive a signal from the A/B input.

Gain Control: There are independent gain controls for the A, B, and SW amplifier sections, each is continuously variable from 200 mV to 6.5 V. When you use the speaker level input, the gain control ranges from 0.8V and 16V.

Crossovers: The A, B, and SW sections also have independent crossover controls. The A and B channels have crossovers that can be configured for Low Pass, High Pass, or Off (Full Range). The rotary frequency controls let you set the crossover point between 40Hz and 500Hz. The SW channel has a low-pass filter with a variable crossover frequency between 40Hz and 500Hz. You can choose a crossover slope of 12dB/octave or 24dB/octave via a 2-way switch.

Remote Bass Boost Control: The included Remote Bass Boost control module lets you adjust the amount of bass (from the subwoofer channel) from the front of the vehicle. The Bass Boost circuit is centered at 50Hz, with a variable boost level of 0 to 18dB. Module dimensions: 1-3/4"W (2-5/8" w/mounting tabs) x 11/16"H x 2" (including knob).

Connections

Power: The power and ground connections are set screw terminals that will accommodate up to 4-gauge wire. The included 3mm Allen wrench is used to tighten and loosen the terminals. Pioneer recommends different power and ground wire gauges based on the length of the wire:

  • 8-Gauge: up to 7' 3"
  • 6-Gauge: up to 11' 10"
  • 4-Gauge: up to 21

The amplifier has three 30A fuses installed. A 4-gauge amplifier wiring kit is recommended with a 90A fuse installed within 18" of the battery.

Remote Turn-on: The remote connection is a set screw terminal that will accommodate up to 8-gauge wire. The included 3mm Allen wrench is used to tighten and loosen the terminals.

Speaker Connections: The speaker output screw terminals for the A and B channels and the SW channel are of different sizes. The terminals for the A and B channels will accept up to 16-gauge speaker wire, while the terminals for the SW channel will accept up to 8-gauge wire. The set screws can be tightened/loosened with the included 3mm and 1.5mm Allen wrenches.

Signal Input: The amplifier features three pairs of stereo RCA inputs for Channels A, B, and SW. If no line level signal is available, use the included speaker level input harness, and splice the speaker wires from the source unit to the harness.

Customer Reviews

Write Your Own Review

You're reviewing: Pioneer GM-D9605 2000Watts Class D 5 Channel Amplifier

How do you rate this product? *

  1 star 2 stars 3 stars 4 stars 5 stars
Value
Quality
Price

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

BRAND & CLIENTS